All public logs

Combined display of all available logs of Make In Salford. You can narrow down the view by selecting a log type, the username (case-sensitive), or the affected page (also case-sensitive).

12:36, 21 December 2023 A.Dunbar talk contribs created page Troubleshooting (OMAX Maxiem 1515) (Created page with "== Startup Problems == === Turning on the air supply causes the bulk abrasive hopper to rattle and make a loud noise. === The tank has depressurised overnight when the air compressors are turned off and the person before you didn't close the AIR IN valve on the bulk abrasive hopper. * Close the '''AIR IN''' valve on the bulk abrasive hopper. * Remove the lid. * Clean the mating surfaces of the seal. * Pull up on the seal T-handle and hold it in place. * Turn '''ON'''...") Tag: Visual edit
12:26, 21 December 2023 A.Dunbar talk contribs moved page Abrasive Garnet (OMAX Maxiem 1515) to Bulk Abrasive Hopper (OMAX Maxiem 1515) without leaving a redirect (More semantic title.)
12:17, 21 December 2023 A.Dunbar talk contribs created page Abrasive Garnet (OMAX Maxiem 1515) (Created page with "== Safety == {{PictogramExplanation|hazard-general|Garnet Bags Are Heavy|Each bag of garnet weights 25 kg. Take care when lifting and moving the bags. Only lift or move the bags if you have completed manual handling training and perform a risk assessment before starting work. }} == Refilling the Abrasive Hopper == Garnet stock is stored on a pallet in the multi-purpose storage room near the SEE Building Goods In. Please ask a member of technical staff to get more from th...") Tag: Visual edit: Switched
11:57, 21 December 2023 A.Dunbar talk contribs created page Vacuum Bed and Wasteboard (AXYZ Innovator) (Created page with "A powerful vacuum pump allows for a lot of flexibility when it comes to positioning work. The vacuum will suck through the MDF wasteboard allowing clamp-free workholding in wide range of circumstances. Safety {{PictogramExplanation|ppe-ear-defenders|Hearing Protection|The vacuum pump is noisy. You must wear passive hearing protection when the vacuum pump is running to prevent irreversible damage to your hearing, even...") Tag: Visual edit: Switched
11:53, 21 December 2023 A.Dunbar talk contribs created page File:Pictogram ppe-ear-defenders.png
11:53, 21 December 2023 A.Dunbar talk contribs uploaded File:Pictogram ppe-ear-defenders.png
11:43, 21 December 2023 A.Dunbar talk contribs created page Function Codes (AXYZ Innovator) (Created page with "To perform certain common operations the CNC router uses function codes - F13 will move the spindle to the current origin point, for example. Often you can pass a variable to the function code, such as picking up a particular tool - F31.1 - or the function will ask further questions once it has loaded. == General Functions == {| class="wikitable" |'''Code''' |'''Description''' |'''Example''' |- |F 1 |Machine Information | |- |F 9 |Delete/Abort Jobs | |} == X/Y Co-ordin...") Tag: Visual edit
11:37, 21 December 2023 A.Dunbar talk contribs created page Troubleshooting (AXYZ Innovator) (Created page with "== Machine Problems == === The machine won't start up - it complains about a missing operating system? === The firmware on the machine controller will try to load new software from any USB stick which is inserted into the machine at start up. * Turn off the machine with the '''POWER OFF''' button. * Unplug the USB drive from the USB socket on the side of the machine electrical cabinet. * Wait at least 30 seconds. * Press the '''POWER ON''' button. * Continue Pow...") Tag: Visual edit
11:25, 21 December 2023 A.Dunbar talk contribs created page Hetty (Hoover) (Created page with "{{Stub}} Hetty is our hoover.") Tag: Visual edit
11:23, 21 December 2023 A.Dunbar talk contribs created page Power Up and Power Down (AXYZ Innovator) (Created page with "== Turning the Machine On == * Turn on the rotary isolator near the office window marked '''ROUTER'''. * Turn on the air supply to the machine, located next to the rotary isolators, marked '''ROUTER AIR'''. * Check the air pressure dial on the regulator at the machine, it should read between 100 and 120 psi. * Check that all of the machine emergency stop switches are released and that the bed is clear of debris. * Ensure the rails are clean and clear of debris so tha...") Tag: Visual edit
18:37, 19 December 2023 A.Dunbar talk contribs deleted page COSHH - Ambersil - Amberclens Foaming Anti-static Cleaner (Experiment)
17:19, 19 December 2023 A.Dunbar talk contribs created page COSHH - Ambersil - Amberclens Anti-static Foaming Cleaner (Creating page via script)
17:13, 19 December 2023 A.Dunbar talk contribs created page COSHH - Ambersil - Amberclens Foaming Anti-static Cleaner (Creating page via COSHH-bot script)
17:10, 19 December 2023 A.Dunbar talk contribs deleted page COSHH - Ambersil - Amberclens Foaming Anti-static Cleaner (content was: "Storage Location: Laser Cutting Area COSHH Cabinet", and the only contributor was "A.Dunbar" (talk))
17:10, 19 December 2023 A.Dunbar talk contribs created page COSHH - Ambersil - Amberclens Foaming Anti-static Cleaner (Creating page via script)
11:54, 19 December 2023 A.Dunbar talk contribs moved page Connecting to the Laser (Epilog Fusion Pro 48) to Connecting to the Laser Cutter (Epilog Fusion Pro 48) without leaving a redirect (Misspelled title)
11:54, 19 December 2023 A.Dunbar talk contribs created page Connecting to the Laser (Epilog Fusion Pro 48) (Created page with "We use Epilog Job Manager and Epilog Dashboard to connect to the laser and send files for cutting and engraving. If it is the first time you've used the laser cutter on a particular PC you will need to add the laser cutter to your user profile. If you wish to use your own laptop you can download and install the latest version of the [https://www.epiloglaser.com/en-uk/tech-support/drivers/fusion-edge-maker-pro-drivers/ Epilog Software Suite]. The Maker Space staf...") Tag: Visual edit
20:09, 18 December 2023 A.Dunbar talk contribs created page Mill 0-1 (Training Part) (Created page with "This introductory part will introduce you using the CAM workspace inside Fusion 360 to prepare work for use with the Haas UMC-500 milling machine in 3-axis mode. You will cover – * Importing a workholding template and 3D model into Fusion 360. * Setting up a workholding template for the stock. * Importing a tool library. * Creating tool paths to face, rough machine, finish contour, and drill material using preset feeds and speeds. * Simulating tool...") Tag: Visual edit
11:57, 18 December 2023 A.Dunbar talk contribs created page File:AXYZ-Innovator-CNC-Router.jpg
11:57, 18 December 2023 A.Dunbar talk contribs uploaded File:AXYZ-Innovator-CNC-Router.jpg
11:25, 18 December 2023 A.Dunbar talk contribs created page File:Haas-st-15y-lathe-chuck.JPG
11:25, 18 December 2023 A.Dunbar talk contribs uploaded File:Haas-st-15y-lathe-chuck.JPG
19:24, 15 December 2023 User account COSHH-bot talk contribs was created by A.Dunbar talk contribs (COSHH bot)
18:46, 15 December 2023 A.Dunbar talk contribs created page Chip Conveyor (Haas ST-15Y) (Created page with "{{SafetyInfoMissing}} Unlike the 5-axis mill this machine has a chip conveyor - it automatically scoops chips and swarf from the bottom of the machine and deposits them into a barrel or chip bin. '''Swarf from a lathe is hazardous - often it is incredibly sharp. It will cut you easily. Do not move swarf around bare handed, and use an appropriate tool when you need to.''' '''Do not touch to interact with any part of the chip conveyor while it is in motion.''' == Oper...") Tag: Visual edit
18:37, 15 December 2023 A.Dunbar talk contribs created page Power Up and Power Down (Haas ST-15Y) (Created page with "== Turning the machine on == * Press the green '''Power On''' button. Follow the instructions that appear on the screen. * Pay special attention to where the turret is located and whether it will collide with anything when it rotates to index itself. == Turning the machine off == '''You must wear work gloves when clearing out swarf from the lathe. Swarf can be incredibly sharp.''' Clean the inside of the machine enclosure using a brush and the air hose. Brush any chi...") Tag: Visual edit
18:24, 15 December 2023 A.Dunbar talk contribs created page ISO Material Codes (Created page with "{{Stub}} == ISO Material Codes == Materials used in CNC machining are split into general groups known as ISO material codes. When you are selecting a turning insert, drill, or other cutting tool you should look at the ISO material group the tool is suited for. This is especially important in turning tool inserts which have geometry which is very specialised and specific to the material group it is designed for. {| class="wikitable" | '''P''' | '''M''' | '''K''' | ''...") Tag: Visual edit
18:14, 15 December 2023 A.Dunbar talk contribs created page File:Klamp-quick-change-tool.jpg
18:14, 15 December 2023 A.Dunbar talk contribs uploaded File:Klamp-quick-change-tool.jpg
18:14, 15 December 2023 A.Dunbar talk contribs created page File:Klamp-collets-dec-2023.jpg
18:14, 15 December 2023 A.Dunbar talk contribs uploaded File:Klamp-collets-dec-2023.jpg
18:00, 15 December 2023 A.Dunbar talk contribs created page File:Haas-st-15y-tailstock-footswitch.jpg
18:00, 15 December 2023 A.Dunbar talk contribs uploaded File:Haas-st-15y-tailstock-footswitch.jpg
17:56, 15 December 2023 A.Dunbar talk contribs created page Tailstock (Haas ST-15Y) (Created page with "In order to support long material the lathe has a hybrid hydraulic-manual tailstock. This tailstock can hold tools with an MT3 taper, such as a live centre. Always remove tools from the tailstock to reduce the risk of collisions with the tool turret. == Inserting tools into the tailstock taper == It is crucially important that the taper of the tool and the taper in the ram of the tailstock is impeccably clean. An...") Tag: Visual edit
17:52, 15 December 2023 A.Dunbar talk contribs created page File:Haas-st-15y-hydraulic-regulator-panel.jpg
17:52, 15 December 2023 A.Dunbar talk contribs uploaded File:Haas-st-15y-hydraulic-regulator-panel.jpg
17:22, 15 December 2023 A.Dunbar talk contribs created page Centres and Centre Drilling (Haas ST-15Y) (Created page with "Workpieces cannot extend more than 4 to 5 times their diameter from the chuck or they start to wobble and whip. With care it is possible to make cuts at such extensions, but heavy cutting work needs to be supported by a live centre in the tailstock. The tailstock is a hybrid manual-hydraulic design. The body of the tailstock must be brought forward toward the chuck, and then the hydraulic quill should be extended so the live centre tip rests securely in the seat created...") Tag: Visual edit
17:20, 15 December 2023 A.Dunbar talk contribs created page File:Centre-drilling.png
17:20, 15 December 2023 A.Dunbar talk contribs uploaded File:Centre-drilling.png
16:54, 15 December 2023 A.Dunbar talk contribs created page Category:Fusion 360 (Created blank page) Tag: Visual edit: Switched
16:54, 15 December 2023 A.Dunbar talk contribs created page Tool Library (Haas UMC-500) (Created page with "{{Stub}} == Fusion 360 Tool Library == The standard tool libraries for the UMC-500 are available on the Microsoft Teams group, under the "CNC Machinery" channel. Look in the Files tab. All the tools - mills, drills, etc. are all in one library and can be filtered down using the facility in Fusion 360's tool library. You should periodically check for a new version of the tool library - it is often updated with new tools or new feeds and speeds. == Tool Numbering ==...") Tag: Visual edit
16:38, 15 December 2023 A.Dunbar talk contribs created page Template:SafetyInfoMissing (Created page with "Category:Safety Information Missing {{fmbox | type = warning | text = This machine or process is missing safety information. Please make sure you check the rick assessments and datasheets in person - ask a member of technical staff if you are unsure. }}")
16:26, 15 December 2023 A.Dunbar talk contribs created page File:Partial-vs-full-threading-inserts.png
16:26, 15 December 2023 A.Dunbar talk contribs uploaded File:Partial-vs-full-threading-inserts.png
14:58, 15 December 2023 A.Dunbar talk contribs created page Threading (Haas ST-15Y) (Created page with "== OD Threads with a partial-form threading insert == A partial form threading insert has a sharp point to it - much sharper than the radiused base of a full-form threading insert. Because of this extra care must be taken to ensure the thread is cut to proper depth. For a longer production run of parts where the thread form has to be perfect it is recommended that you use a full profile threading insert. If you are trying to cut a thread and it just seems like it isn't...") Tag: Visual edit
14:56, 15 December 2023 A.Dunbar talk contribs created page File:Thread-form-diagram.png
14:56, 15 December 2023 A.Dunbar talk contribs uploaded File:Thread-form-diagram.png
14:48, 15 December 2023 A.Dunbar talk contribs created page Troubleshooting (Haas ST-15Y) (Created page with "== Program/CAM Problems == thumb|250x250px|Live Tool checkbox in the Post Processor tab of the tool editor. === When I start drilling a hole the live tooling motor turns on and the main spindle doesn't turn. === Don't try to drill with a static tool and a static spindle - it won't work! You have the "Live Tool" option selected in the Post Processor tab of the tool you are trying to drill with. Uncheck this box to use the main spin...") Tag: Visual edit
14:47, 15 December 2023 A.Dunbar talk contribs created page File:F360-live-tool-checkbox.png
14:47, 15 December 2023 A.Dunbar talk contribs uploaded File:F360-live-tool-checkbox.png
12:39, 15 December 2023 A.Dunbar talk contribs created page Tool Library (Haas ST-15Y) (Created page with "{{Stub}} == Tool 9999 == Tools which do not typically live in the lathe are referred to in the Fusion 360 Tool Library as tool number 9999. You must load the tools into the machine in slots which make sense and will not cause a collision or crash. Update the tool number in Fusion 360 by right clicking on an operation which uses the tool, selecting "Edit Tool" and then change the tool number in the Post Processor tab. If you forget to update this value the post process...") Tag: Visual edit