== Power Up ==
|Turn on the wall mounted water valves (one for hose and one for pump)
...
5 KB (814 words) - 12:43, 2 December 2024
* Press the green '''Power On''' button. Follow the instructions that appear on the screen.
== Warming up the machine ==
...
3 KB (503 words) - 18:51, 15 December 2023
* Press the green '''Power On''' button. Follow the instructions that appear on the screen.
* Pay special attention to where the turret is located and whether it will collide with anything when it rotates to index itself.
...
3 KB (484 words) - 18:51, 15 December 2023
...e corner of the machine near the CNC mill door. It should read between 100 and 120 psi.
...ris. There are three emergency stop buttons - on either side of the gantry and one on the machine control pendant.
...
3 KB (506 words) - 15:02, 14 February 2025
== Power Up ==
* Ensure the work area is clean and free of general debris and flammable material.
...
4 KB (691 words) - 12:13, 29 December 2023
== Power Up ==
* Turn the key switch marked "Power" to the on position.
...
1 KB (200 words) - 09:41, 2 April 2025
...[Nikon Altera 10108|CMM]] is a complicated precision measurement equipment and can be damaged easily if it isn't turned on properly.
...if required. Use a clean paper towel and ensure the bearing area is clean and dry.
...
2 KB (336 words) - 19:04, 15 December 2023
== Power Up ==
* Turn the key switch marked "Power" to the on position.
...
1 KB (200 words) - 09:41, 2 April 2025
...Follow the instructions on the [[Training (AXYZ Innovator)|Training page]] and prepare the files for cutting before you attend the session.
== Power Up and Power Down ==
...
3 KB (426 words) - 15:01, 14 February 2025
This is a guide to how pages on the wiki should be created and written, in order to keep things consistent.
== Page Names and Titles ==
...
2 KB (363 words) - 18:11, 15 December 2023
=== The machine won't start up - it complains about a missing operating system? ===
...ew software from any USB stick which is inserted into the machine at start up.
...
1 KB (216 words) - 12:39, 27 February 2024
...three individually controllable outputs - two are capable of up to 30V, 3A and another is capable of 5V 3A.
...
220 bytes (34 words) - 12:15, 13 December 2023
...Common in a machine shop environment they can be used as a way to quickly and repeatedly measure machined parts to ensure they are within tolerance.
Our machine can also be fitted with a laser scanning head so that delicate and more "organic" surfaces can be measured accurately.
...
3 KB (522 words) - 15:58, 8 January 2024
...e corner of the machine near the CNC mill door. It should read between 100 and 120 psi.
...ris. There are three emergency stop buttons - on either side of the gantry and one on the machine control pendant.
...
3 KB (506 words) - 15:02, 14 February 2025
* Press the green '''Power On''' button. Follow the instructions that appear on the screen.
* Pay special attention to where the turret is located and whether it will collide with anything when it rotates to index itself.
...
3 KB (484 words) - 18:51, 15 December 2023
== Power Up ==
* Ensure the work area is clean and free of general debris and flammable material.
...
4 KB (691 words) - 12:13, 29 December 2023
* Press the green '''Power On''' button. Follow the instructions that appear on the screen.
== Warming up the machine ==
...
3 KB (503 words) - 18:51, 15 December 2023
...g both ferrous and non-ferrous metals as well as an assortment of plastics and dense modelling foams. It uses a spinning cutting tool such as an endmill o
...t and repositioning it in the machine. This allows much faster prototyping and faster turnaround times for one off parts.
...
4 KB (657 words) - 18:05, 10 January 2024
...[Nikon Altera 10108|CMM]] is a complicated precision measurement equipment and can be damaged easily if it isn't turned on properly.
...if required. Use a clean paper towel and ensure the bearing area is clean and dry.
...
2 KB (336 words) - 19:04, 15 December 2023
...on|hazard-flammable|Fire Hazard|Material may catch alight during engraving and cutting. }}
...e is operated with interlocks defeated. This can cause immediate blindness and burns.}}
...
5 KB (750 words) - 12:28, 29 December 2023
...including but not limited to aluminium, steel, ceramics, glass, rockwool, and composites! Pretty much the only thing it can't cut is toughened, or temper
Mains water is pressurised up to 45,000 PSI (~3000 bar) and then mixed with an abrasive garnet. This mixture "sands" its way through th
...
4 KB (565 words) - 12:50, 2 December 2024
...ssibilities even more by allowing work to take place off the spindle axis, and perpendicular to it as well.
== Power Up and Power Down ==
...
5 KB (775 words) - 10:56, 2 August 2024
== Power Up ==
|Turn on the wall mounted water valves (one for hose and one for pump)
...
5 KB (814 words) - 12:43, 2 December 2024
...le of supplying up to 200 amps of welding current, and can weld in both AC and DC modes. It is capable of also working as a stick/arc welder but the weldi
Welding is an inherently risky process involving electricity and very high temperatures - you are literally melting steel.
...
5 KB (929 words) - 12:32, 10 July 2024
...ser to sinter finely ground nylon powder into solid parts. The un-sintered power supports the parts as they are printing so you don't need to include suppor
...ity of typically 30% - this means that we will batch various jobs together and print them all at the same time.
...
982 bytes (167 words) - 11:13, 13 December 2023
...duction run has very different goals and targets so will approach roughing and finishing differently.
== Warm up the machine ==
...
5 KB (815 words) - 15:05, 11 April 2025
|[[File:Epilog-fusion-pro-48-power-switch.jpg|thumb|none]]
Wait for the machine to start up and home itself before continuing with the next steps.
...
2 KB (238 words) - 08:39, 17 May 2024
